How to Install a Bar-End Mirror on Your Bike

Checking traffic behind you means a look over your left shoulder, and in that second it’s easy to drift toward the lane. A bar-end mirror turns that into a quick glance down.

The job itself is simple. Pull the end plug, slide the mirror’s mount in, tighten it to the maker’s torque and aim the glass from the saddle. Allow about 15 minutes. The real work is the check before you buy: can your bar end take that mirror?

If you’re still choosing a model, start with our picks of the best bike mirrors for handlebars and helmets.

Check Your Bar End Before You Buy

Most bar-end mirrors use an expander, a sleeve or wedge that swells inside the bar as you tighten a center bolt. Some press in as a push-fit insert with no bolt. Clamp-on mounts bolt around the outside of the bar and go by its outside diameter.

Pull your end plug and look. An open tube is only the first check. Three more decide whether a plug-in mirror will hold:

  • Inside diameter. Measure the opening with a caliper and compare it with the mirror’s listed range. Ergon’s RM Touring takes 17.2 to 22 mm, and CatEye lists 16 to 25.4 mm for its BM-45.
  • Insertion depth. The mount needs enough clear tube to sit fully home. Internal cables or a part fixed inside the bar can stop it short.
  • Sleeve or wedge. If the mirror ships with more than one, fit the one its instructions call for at your diameter.

A closed grip doesn’t rule out a plug-in mirror. A removable end cap or a carefully trimmed grip end can expose a usable tube.

Your SetupAt the Bar EndLikely MountCheck First
Flat bar, open gripsPush-in plugPlug-inDiameter and depth
Flat bar, closed gripsGrip end capTrim cap, then plug-inCut the cap only
Lock-on gripsCollar and end capPlug-in if the cap comes outSome caps don’t
Drop barPlug holding the tapeMirror listed for drop barsTape tail stays tucked
Bar-end shiftersThe shifterClamp-on or helmet mirrorNo open tube
Carbon barEnd plugOnly if both makers allow itSome mirrors exclude carbon

Carbon bars need one more check. Use an expanding mount in one only when both the bar maker and the mirror maker permit that combination. Then stay inside their installation limits. Some mirrors rule carbon out. The Ergon RM Touring instructions, for one, say it isn’t suitable for carbon bars.

Left Side, and Mind the Width

In the US, passing traffic comes up on your left, so the mirror goes on the left bar end. One mirror there is enough for most riders.

The catch on flat bars is width. The mirror becomes the widest point of the bike, so it clips door frames and bikes on a rack. Every knock throws off the aim. If you park in tight spots, I’d pick one whose arm folds or pops off.

Width matters less on narrower drop bars. Bar shape changes the view, though. A flat bar’s end faces sideways, while a drop bar’s end points back.

Choose a mirror its maker lists as compatible with your bar shape, with enough adjustment to aim rearward from that end. Some cover both. The CatEye BM-45 is listed for drop and flat bars and lists at $19.95 (as of October 2026).

Fitting the Mirror, Step by Step

You’ll need the hex key for your mirror’s bolt, a caliper, and a flat screwdriver or plastic tire lever. Add a utility knife if your grips have closed ends.

If the instructions list a tightening torque, add a torque wrench that reads in that range. Numbers vary. Ergon caps the RM Touring at 1.5 N·m (1.1 ft-lb), while CatEye specs 8.5 N·m for the BM-45.

Expanding Plug-In Mounts

These steps are for mounts that lock in with an expanding sleeve or wedge.

  1. Remove the old plug. Pry out a push-in plug. Loosen the center screw on an expanding one first. On drop bars, hold the tape tail in place.
  2. Open and clean the tube. On a closed grip, trim off only the end cap and keep the blade off the bar. Or swap to open-end grips. Wipe out grease with rubbing alcohol so the expander can bite.
  3. Fit the sleeve and insert. Use the sleeve or wedge specified for your diameter. Back the bolt out a few turns and slide the mount in until its flange sits flush.
  4. Set the rough angle. It’s easier to turn the arm now than once the plug is locked.
  5. Tighten to spec. Bring the bolt to the listed torque and stop. If the mount still turns, don’t go past the limit. Pull it and recheck the diameter, sleeve and depth.
  6. Aim the glass. Do it from the saddle (see below).

Use threadlocker only if the mirror manufacturer’s instructions specify it.

On drop bars, the mirror’s plug also holds the tape tail. If the tape comes loose while you’re in there, rewrap the bar tape before the mirror goes in.

Push-Fit Inserts

Some plug-in mirrors have no bolt. Sprintech’s drop-bar Racing models press in on a rubber cap, with no tools. Their installation guidance lists a 20 mm minimum bar diameter and notes that seating the cap takes some force. The tape can stay on.

A little soap helps the cap slide in. Skip grease or oil, which makes the mirror less stable. If something inside the bar blocks the cap, have a mechanic remove it.

Clamp-On Mounts

A clamp-on mount holds best on bare bar, since grip rubber and tape let it creep. Close it around a clear spot near the end, tighten it to the listed torque, then aim it. Check its fit list against your exact bar before you order.

Aim It From the Saddle

Set the angle sitting on the bike in your normal riding position. Have a friend hold it, or put a foot down against a wall.

Adjust until the lane behind you fills most of the glass. Leave a sliver of your arm or shoulder at the inner edge as a reference. On drop bars, set it from the hand position you use most, since the view shifts between hoods and drops.

Keep turning your head before you move left, too. A small mirror, especially a convex one, makes cars look farther away than they are.

Check Clearance, Then Ride a Short Loop

Before you roll anywhere, make sure the mirror stays out of the way.

  • Turn the handlebar fully left and right. The mirror shouldn’t touch the frame, cables or anything mounted up front.
  • Squeeze both brakes and run through the gears. Levers and shifters need their full travel with no contact.
  • Try every hand position you use. On drop bars, settle into the drops and check that your hands and knees clear the mirror.
  • On an e-bike, check that the mirror doesn’t block the throttle or any other control.

Then ride a short loop over rough pavement and look again. If the mount or arm has moved, find out why before a longer ride. Ergon tells RM Touring owners to recheck the torque after the first ride or 50 km (about 31 miles), then periodically. I’d keep that habit with any bar-end mirror.

If your bar end fails any of the fit checks, go with a clamp-on or helmet mirror. If it passes, I’d put a bar-end mirror on the left before your next ride.

Bar-End Mirror Questions

Can You Put a Bar-End Mirror on Drop Bars?

Yes, if its maker lists it for drop bars and it can aim rearward from an end that already points back.

Do Motorcycle Bar-End Mirrors Fit a Bicycle?

I wouldn’t try it. Motorcycle versions usually replace bar-end weights, and their adapters are sized for motorcycle bars. Buy one made for bikes.

Why Does My Bar-End Mirror Keep Turning?

First, find which part is moving. If the whole mount spins in the bar end, the expander isn’t holding. Check the torque, grease in the tube, your diameter and the sleeve or wedge. Don’t tighten past the limit to make it stop.

If the mount stays put but the arm or glass loses its angle, leave the expander alone. Check the arm joint or the pivot behind the mirror head, and adjust it the way the mirror’s instructions describe.

Is a Bar-End Mirror Safe on a Carbon Handlebar?

Only when both the bar maker and the mirror maker permit an expanding mount in that bar, and only within their limits. Some mirrors exclude carbon bars outright.

How Do I Mount a Mirror If My Bar Ends Are Blocked?

See whether the block comes out first. If a bar-end shifter or fixed part fills the end, use a clamp-on mount. If nothing fits, a helmet or eyeglass mirror needs no handlebar work.

Photo: Did you book your bike^ – geograph.org.uk – 7939633 by Mr Ignavy, CC BY-SA 2.0, via Wikimedia Commons. Cropped.

Bicycling Land Editors
Bicycling Land Editorshttps://bicyclingland.com/about/
The Bicycling Land editors research bikes, e-bikes and cycling gear for US riders. Recommendations are built on manufacturer specifications, independent reviews, owner reports and safety records, with every claim linked to its source. Read how we work on our editorial policy page.

Popular Guides

Related Articles